spec no: dsao1007 rev no: v.1b date: jan/06/2015 page: 1 of 5 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203013895 3.0mmx1.5mm smd chip led lamp attention observe precautions for handling electrostatic discharge sensitive devices part number: apl3015zgck-f01 green features z 3.0mmx1.5mm smt led, 1.4mm thickness. z low power consumption. z ideal for backlight and indicator. z package : 2000pcs / reel. z moisture sensitivity level : level 3. z rohs compliant. descriptions z the green source color devices are made with ingan on sapphire light emitting diode. z electrostatic discharge and power surge could damage the leds. z it is recommended to use a wrist band or anti- electrostatic gl ove when handling the leds. z all devices, equipments and machineries must be electrically grounded. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.2(0.008") unless otherwise noted. 3. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice . 4.the device has a single mounting surface. the device must be mounted according to the specifications.
spec no: dsao1007 rev no: v.1b date: jan/06/2015 page: 2 of 5 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203013895 selection guide notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. luminous intensity/ luminous flux: +/-15%. 3. luminous intensity value is traceable to the cie127-2007 compliant national standards. absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c notes: 1.wavelength: +/-1nm. 2.forward voltage: +/-0.1v. 3.wavelength value is traceable to the cie127-2007 compliant national standards. 4.excess driving current and/or operating temperature higher t han recommended conditions may result in severe light degradation or premature failure. note: 1. 1/10 duty cycle, 0.1ms pulse width. part no. dice lens type v iewing angle [1] min. typ. 2 1/2 apl3015zgck-f01 green (ingan) water clear 500 700 70 iv (mcd) [2] @ 20ma symbol parameter device typ. max. units test conditions peak peak wavelength green 515 nm i f =20ma d [1] dominant wavelength green 525 nm i f =20ma ? 1/2 spectral line half-width green 35 nm i f =20ma c capacitance green 45 pf v f =0v;f=1mhz v f [2] forward voltage green 3.3 4.1 v i f =20ma i r reverse current green 50 ua v r =5v parameter green units power dissipation 102.5 mw dc forward current 25 ma peak forward current [1] 150 ma reverse voltage 5 v operating temperature -40c to +85c storage temperature -40c to +85c
spec no: dsao1007 rev no: v.1b date: jan/06/2015 page: 3 of 5 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203013895 green apl3015zgck-f01
spec no: dsao1007 rev no: v.1b date: jan/06/2015 page: 4 of 5 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203013895 apl3015zgck-f01 reflow soldering is recommended and the soldering profile is shown below. other soldering methods are not recommended as they might cause damage to the product. recommended soldering pattern (units : mm; tolerance: 0.1) reel dimension tape dimensions (units : mm)
spec no: dsao1007 rev no: v.1b date: jan/06/2015 page: 5 of 5 approved: wynec checked: allen liu drawn: l.q.xie erp: 1203013895 packing & label specifications apl3015zgck-f01 terms and conditions for the usage of this document 1.the information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before product ion usage customer should refer to the latest datasheet for the updated specifications. 3.when using the products referenced in this docu ment, please make sure the product is being operated within the environmental and electrical limit s specified in the datasheet. if customer usage exceeds the specified limits, kingbright w ill not be responsible for any subsequent issues. 4.the information in this document applies to typical usage in consumer electronics applications. if customer's application has special reliabilit y requirements or have life-threatening liabilities, such as automotive or medical usage, please co nsult with kingbright representative for further assistance. 5.the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6.all design applications should refer to kingbr ight application notes available at http://www.kingbrightusa. com/applicationnotes
|
